Shipping class: shipping rate by weight

Shipping by weight

GG&G Mossberg 500/590 Ambi Looped Rear Sling Attachment

Mossberg 500/590 Ambi  Looped Rear Sling Attachment

MOSSBERG 590 AMBIDEXTROUS LOOPED REAR SLING ATTACHMENT SPECIFICATIONS:
  • Installs easily with common hand tools.
  • Accommodates slings with MASH or HK style hooks.
  • This dual loop configuration accommodates a right and left hand shooter. It was designed, manufactured and tested for departments that issue 500/590 shotguns on a daily basis to both right and left handed shooters.
  • The Mossberg Rear Sling Attachment will also fit the Mossberg 500 and Maverick 88.
  • Can be used as a single point sling or a dual point sling attachment.
  • When used as a Mossberg Single Point Looped Sling Attachment, it allows the operator to mount the weapon on either the primary or offside shoulder. As a result, during dynamic entries it becomes easier to “cut the pie” at doorways and move around corners, whether they are on the right side or left side, without telegraphing the operator’s position. In addition, slings attached to a single point mount work especially well when operators are deployed wearing body armor or are involved in breaching operations.
  • All edges are dehorned and smoothed for shooter’s safety.
  • Material: Precision machined from 7075 aircraft grade solid billet aluminum alloy.
  • Finish: Type III hard coat anodized non-reflective matte black per Mil-Spec.
  • Rear sling attachment will add 0.235″ to the length of pull on the stock and may require a longer stock bolt.
  • Weight: Less than 1 oz.
  • Warranty: Lifetime.
  • Made In America By Men And Women Proud To Be Americans!

GG&G Mossberg 500/590 Rear Single Looped RH Sling Attachment

Mossberg 500/590 Rear Single Looped RH Sling Attachment

MOSSBERG 500/590 LOOPED REAR SLING ATTACHMENT:

The Mossberg 500/590 Looped Rear Sling Attachment can be used in conventional dual point sling setups as well as single point sling set ups. 

 
MOSSBERG 500/590 LOOPED REAR SLING ATTACHMENT SPECIFICATIONS:
  • Installs easily with common hand tools.
  • Accommodates slings with MASH or HK style hooks.
  • When used as a Mossberg 500/590 Single Point Looped Sling Attachment, it allows the operator to mount the weapon on either the primary or offside shoulder. As a result, during dynamic entries it becomes easier to “cut the pie” at doorways and move around corners, whether they are on the right side or left side, without telegraphing the operator’s position. In addition, slings attached to a single point mount work especially well when operators are deployed wearing body armor or are involved in breaching operations.
  • All edges have been dehorned and smoothed for shooter’s safety.
  • Material: Precision machined from 7075 aircraft grade solid billet aluminum alloy.
  • Finish: Type III hard coat anodized non-reflective matte black per Mil-Spec.
  • Rear sling attachment will add 0.235″ to the length of pull on the stock and may require a longer stock bolt.
  • Weight: Less than 1 oz.
  • Warranty: Lifetime.
  • Made In America By Men And Women Proud To Be Americans!

GG&G Mossberg 590 Rear Sling Attachment

SlingMossberg 590 Rear Sling Attachment

  • Compact & easy to install.
  • Be advised, the Mossberg 590 Rear Sling Attachment adds 1/8″ to the length of pull.
  • Designed and manufactured to withstand the rigors associated with professional use.
  • The Mossberg 590 Rear Sling Attachment will not fit the Blackhawk, Knoxx Spec-Ops Recoil Compensating Stock.
  • The Mossberg 590 Rear Sling Attachment mounts just behind the receiver.
  • The GG&G 590 Rear Sling Attachment provides the preferred rear side sling mounting position for 1 1/4″ slings.
  • This 590 Rear Sling Attachment can be used with a two point sling set up or as a single point sling attachment.
  • When used as a 590 Single Point Sling Attachment, it allows the operator to mount the weapon on either the primary or offside shoulder. As a result, during dynamic entries it becomes easier to “cut the pie” at doorways and move around corners, whether they are on the right side or left side, without telegraphing the operator’s position. In addition, slings attached to a single point mount work especially well when operators are deployed wearing body armor or are involved in breaching operations.
  • Also fits 12 gauge Mossberg 500’s and Maverick 88’s.
  • All edges have been dehorned and rounded for the shooters safety.
  • Material: Manufactured from solid billet 7075-T6 aluminum.
  • Finish: Bead blasted and Type III Hard coat anodized in non-reflective matte black per Mil-Spec.
  • Rear sling attachment will add 0.235″ to the length of pull on the stock and may require a longer stock bolt.
  • Weight: 1.2 oz.
  • Warranty: Lifetime.
  • Made In America By Men And Women Proud To Be Americans!

GG&G Mossberg Shockwave Rear Sling Attachment

Mossberg Shockwave Rear Sling Attachment

The Mossberg Shockwave 12ga shotgun is an exciting and popular addition to the Mossberg shotgun lineup. It is indeed a “Modern Day Six-Shooter”. Shotgunners today like the tactical flexibility that a quick detach sling provides.

GG&G has developed a solution for those shooters with the Mossberg Shockwave, The Mossberg Shockwave Quick Detach Rear Sling Attachment. This QD rear sling attachment provides an excellent single point sling set up. The GG&G Shockwave QD Sling Mount comes as a Heavy Duty Rectangular QD Sling Swivel that accommodates 1 1/4″ webbing.

Specifications:

  • Compact and easy to install.
  • Manufactured specifically for the Shockwave 12ga . Will not fit the Shockwave 20ga.
  • IMPORTANT: Unlike other similar products on the market, the GG&G Mossberg Shockwave QD Sling Attachment does not incorporate an attachment nut on the side opposite the sling swivel. GG&G uses a smooth button head cap screw as shown in the image above.
  • Complete installation instructions included.
  • No modification to shotgun required.
  • Designed and manufactured to withstand the rigors associated with professional use.
  • Ambidextrous.
  • Provides a side mounted QD sling mount.
  • Places the sling attachment out onto the receiver reducing the possibility of hand contact under recoil.
  • Mossberg Shockwave Sling Mount protrudes just .53 of an inch from face of receiver.
  • With just a push of the QD button, unsling your Mossberg Shockwave shotgun for tactical flexibility.
  • Available with the GG&G 1 ¼” HD Sling Swivel
  • QD Rectangular Sling Swivel accommodates up to 1 1/4″ slings.
  • Package includes two Delrin washers to protect both faces of the Mossberg receiver.
  • Once installed, the button head is the only thing visible on the side of the receiver opposite the sling swivel.
  • Both the swivel cup and the screw are parkerized to closely match the receiver finish of your Shockwave.
  • All edges have been dehorned for shooter’s safety.
  • Material: Manufactured from tough 4140 steel.
  • Finish: Bead blasted and manganese phosphated in a non-reflective matte black finish per mil-spec.
  • Weight: 2 oz with the HD QD Sling Swivel installed.
  • Warranty: Lifetime.
  • Made in America By Men And Women Proud To Be Americans!

Raptor Grip 870

Raptor™ Grip 870

The Remington 870 grip / Raptor Grip designed by Shockwave Technologies is MADE IN AMERICA. With its enhanced texture, you gain a great hold on your weapon. Its glass-filled polymer construction is virtually indestructible.

This is a new style of bird’s head grip (aka birdshead grip aka witness protection grip aka chicken head grip aka border patrol grip aka entry-style grip aka bad ass grip) developed and manufactured by Shockwave Technologies, LLC in the U.S.A.

The Raptor Grip is molded of a super-tough glass-filled polymer and fits:

  • Remington 870 12-gauge firearms
  • New England Firearms (NEF) Pardner Pump Protector 12-gauge
  • Harrington & Richardson (H&R) Pardner Pump Protector 12-gauge
  • Interstate Arms Corp (IAC) Hawk Model 98 12-gauge
  • Interstate Arms Corp (IAC) Hawk Model 982 12-gauge
  • Interstate Arms Corp (IAC) Hawk Model 981R 12-gauge

Unique angle of the Raptor Grip minimizes felt recoil, allowing maximum control shot after shot. It also just looks badass. Order yours today. Yes, mounting hardware is included. (Requires a 3/16” hex wrench for installation, which is not included.)

Firearm is not included.

*Note that a pistol-grip-only Remington 870 firearm with a 14” barrel and the Raptor Grip installed measures 26.5” in overall length (measured parallel to the bore). The grip itself adds 5.5” to the length of the weapon (measured parallel to the bore).

Of course, the Raptor grip also fits 12-gauges with 18.5”, 20”, and longer barrels.

*Note that there is no predefined hole for a sling swivel stud on the Raptor Grip. This allows you to put your sling swivel wherever you want it on the grip—not just where we think it should go. Just drill a 1/8” pilot hole, and thread in your sling swivel stud.

 

Raptor F1 Forend for Remington 870/Tac 14

Raptor™

F1 Forend for Remington 870 and Tac 14

The Shockwave Technologies Raptor F1 Forend for Remington 870 and Tac 14 includes options to add the Raptor Grip, Heat Shield and Forend nut tool, all MADE IN AMERICA. Its strong nylon construction is virtually indestructible.

Forend Features include:

  • Rugged nylon construction
  • Lightweight
  • Available in Black, FDE, OD Green and Gray
  • Extra length lets you personalize forward handhold
  • Ribbed inset area provides secure gripping
  • Front and rear handstops improve safety
  • A total of 10 M-LOK® slots for mounting lights, vertical grips, angled grips, Picatinny rails, and more
  • Includes the upper heat shield to prevents burns and offers rifle sights for fast target acquisition
  • Options include the forend wrench to simplify and speed installation
  • Compatible with Remington 870 and Tac 14 12-gauge firearms
  • Veteran designed
  • Made in U.S.A.

The Raptor Grip is available in Black, FDE, OD Green and Gray. It is molded of a super-tough glass-filled polymer.

Installation instructions

Firearm shown is not included.

The Raptor F1 heat shield is not compatible with receiver-mounted rails 

Be sure to closely check fit, function, and clearance — many receiver-mounted accessories are NOT compatible with the Raptor F1.**

Raptor Grip 870 with QD

Raptor Grip 870 with QD

The Shockwave Technologies Raptor Grip with QD cup is MADE IN AMERICA. With its enhanced texture, you gain a great hold on your weapon. Its glass-filled polymer construction is virtually indestructible. This is a new style of bird’s head grip (aka birdshead grip aka witness protection grip aka chicken head grip aka border patrol grip aka entry-style grip aka bad ass grip) and QD cup is developed and manufactured by Shockwave Technologies, LLC in the U.S.A.

The Raptor Grip is molded of a super-tough glass-filled polymer and fits:

  • Remington 870 12-gauge firearms
  • New England Firearms (NEF) Pardner Pump Protector 12-gauge
  • Harrington & Richardson (H&R) Pardner Pump Protector 12-gauge
  • Interstate Arms Corp (IAC) Hawk Model 98 12-gauge
  • Interstate Arms Corp (IAC) Hawk Model 982 12-gauge
  • Interstate Arms Corp (IAC) Hawk Model 981R 12-gauge

Unique angle of the Raptor Grip minimizes felt recoil, allowing maximum control shot after shot. It also just looks badass. Order yours today. Yes, mounting hardware is included. (Requires a 3/16” hex wrench for installation, which is not included.)

 

*Firearm and QD swivel shown is not included.*

 

*Note that a pistol-grip-only Remington 870 firearm with a 14” barrel and the Raptor Grip installed measures 26.5” in overall length (measured parallel to the bore). The grip itself adds 5.5” to the length of the weapon (measured parallel to the bore).

Of course, the Raptor grip also fits 12-gauges with 18.5”, 20”, and longer barrels.

 

 

 

Raptor Grip 870 20-gauge + adapter

Raptor™ Grip for Remington 870 20-gauge + Mesa Tactical Adapter

The Shockwave Technologies Raptor Grip is MADE IN AMERICA. With its enhanced texture, you gain a great hold on your weapon. Its glass-filled polymer construction is virtually indestructible.

This is a new style of bird’s head grip (aka birdshead grip aka witness protection grip aka chicken head grip aka border patrol grip aka entry-style grip aka bad ass grip) developed and manufactured by Shockwave Technologies, LLC in the U.S.A.

The Raptor Grip is molded of a super-tough glass-filled polymer.

Mesa Tactical’s 20 gauge to 12 gauge adapter included.  Simply a attached at the receiver in place of the standard 20 gauge stock, this cast steel adapter enables the use of the Raptor 12 gauge Remington 870 grip.

Unique angle of the Raptor Grip minimizes felt recoil, allowing maximum control shot after shot. It also just looks badass. Order yours today. Yes, mounting hardware is included. (Requires a 3/16” hex wrench for installation, which is not included.)

Firearm is not included.

*Note that a pistol-grip-only Remington 870 firearm with a 14” barrel and the Raptor Grip installed measures 26.5” in overall length (measured parallel to the bore). The grip itself adds 5.5” to the length of the weapon (measured parallel to the bore).

Of course, the Raptor grip also fits 20-gauges with 18.5”, 20”, and longer barrels.

*Note that there is no predefined hole for a sling swivel stud on the Raptor Grip. This allows you to put your sling swivel wherever you want it on the grip—not just where we think it should go. Just drill a 1/8” pilot hole, and thread in your sling swivel stud.

Raptor Grip 870 with QD 20-gauge + adapter

Raptor™ Grip for Remington 870 20-gauge with QD + Mesa Tactical Adapter

The Shockwave Technologies Raptor Grip with QD cup is MADE IN AMERICA. With its enhanced texture, you gain a great hold on your weapon. Its glass-filled polymer construction is virtually indestructible.

This is a new style of bird’s head grip (aka birdshead grip aka witness protection grip aka chicken head grip aka border patrol grip aka entry-style grip aka bad ass grip) and QD cup is developed and manufactured by Shockwave Technologies, LLC in the U.S.A.

The Raptor Grip is molded of a super-tough glass-filled polymer.

Mesa Tactical’s 20 gauge to 12 gauge adapter included.  Simply attached at the receiver in place of the standard 20 gauge stock, this cast steel adapter enables the use of the Raptor 12 gauge Remington 870 grip.

Unique angle of the Raptor Grip minimizes felt recoil, allowing maximum control shot after shot. It also just looks badass. Order yours today. Yes, mounting hardware is included. (Requires a 3/16” hex wrench for installation, which is not included.)

 

*Firearm and QD swivel shown is not included.*

 

*Note that a pistol-grip-only Remington 870 firearm with a 14” barrel and the Raptor Grip installed measures 26.5” in overall length (measured parallel to the bore). The grip itself adds 5.5” to the length of the weapon (measured parallel to the bore).

Of course, the Raptor grip also fits 20-gauges with 18.5”, 20”, and longer barrels.

 

Raptor Strap Kit 870 Forend

Raptor™ Strap Kit for Remington 870 Forend

Raptor Strap kit for the Remington 870 forend. Designed for the tactical forearm shown, but will also fit the standard hand guard styles. It will also fit other shotgun models from other manufacturers.

The Raptor Strap kit includes the strap, attachment hardware, and detailed instructions with full-size template. (Forearm pictured is not included—just the forearm strap kit.)

Easy installation, takes about 10 minutes. Improves handling immensely!

Requires a drill with an 1/8″ drill bit and a Phillips head screwdriver for installation.

GG&G Remington 870 Follower

Remington 870 Follower

THE REMINGTON 870 FOLLOWER:

Remington 870 Shotgun shooters know that the standard factory Remington 870 follower leaves much to be desired. It is unreliable and does not offer the necessary features tactical shooters are looking for. It is one of the first 870 shotgun components to be upgraded. The GG&G Remington 870 Follower for 12 ga. shotguns are enhanced followers manufactured with the tactical shooter in mind.

REMINGTON 870 STANDARD MAGAZINE FOLLOWER SPECIFICATIONS:

  • The GG&G Enhanced 870 Follower fits the Remington 870, 1100 and 1187 12 ga. shotguns.
  • Installs just like the factory 870 follower.
  • The follower is manufactured with a deep spring pocket to better control spring movement.
  • The GG&G Remington Stainless Steel Follower is CNC precision machined from stainless steel for corrosion and wear resistance. The slotted stainless steel body provides smooth operation and resists galling and contaminants from imbedding into the body of the follower. These are the two major contributors to aftermarket followers malfunctioning.
  • Material 1: The body of the follower is precision machined from 300 series stainless steel.
  • Material 2: The high visibility red insert is 6061 T6 aluminum and is manufactured so that you cannot only quickly see that the magazine tube is empty, but in low light conditions, feel the difference between the face of the follower and the rear of a shotgun shell.
  • Finish 1: The body of the follower is polished stainless.
  • Finish 2: The aluminum insert is anodized an eye catching bright rocket red.
  • Weight: .6 oz.
  • Warranty: Lifetime.
  • Made In America By Men And Women Proud To Be Americans!

GG&G Remington Tac 14 Follower

Remington Tac 14 Follower

REMINGTON TAC-14 MAGAZINE FOLLOWER SPECIFICATIONS:

  • The GG&G Enhanced Remington TAC-14 Follower is manufactured specifically for TAC-14 870 12ga shotgun. 
  • Installs just like the factory 870 follower.
  • The GG&G Remington TAC-14 Follower is manufactured from stainless steel for corrosion and wear resistance. The slotted stainless steel body provides smooth operation and resists galling and contaminants imbedding into the body of the follower. These are the two major contributors to aftermarket followers malfunctioning.
  • The high visibility red insert is aluminum and is manufactured so that you cannot only quickly see that the magazine tube is empty, but in low light conditions, feel the difference between the face of the follower and the rear of a shotgun shell.
  • The follower is manufactured with a deep spring pocket to better control spring movement.
  • Weight: .6 oz.
  • Warranty: Lifetime.
  • Made In America By Men And Women Proud To Be Americans!

GG&G Remington 870 Three Mounting Hole Scope Mount

Remington 870 Three Mounting Hold Scope Mount

  • REMINGTON 870 THREE MOUNTING HOLE SCOPE MOUNT

    The GG&G one piece Remington 870 Scope Mount With Three Mounting Holes, is manufactured for the new 870 Shotgun being manufactured by RemArms that has three tapped holes versus the previous four tapped holes in the top of the receiver.  This 870 Receiver Scope Mount, provides a super easy way to mount a tactical scope to the factory drilled and tapped receiver of your Remington 870 shotgun. The design of the Remington 870 Scope Mount provides that low-profile “factory built and installed” look.

    REMINGTON 870 THREE HOLE MOUNTING SCOPE MOUNT SPECIFICATIONS:

    • Low profile.
    • MIL-STD-1913 configuration.
    • Excellent for mounting a tactical scope to your RemArms Remington 870 shotgun.
    • Easy installation to factory three hole tapped receivers with 6-48 threads.
    • Attaches with three steel Torx head screws. Torx wrench is included.
    • The Remington 870 Scope Mount is precision machined from 6061-T6 billet aluminum.
    • All edges are smoothed and rounded for the shooter’s safety.
    • Finish: Type III hard coat anodized in a non-reflective matte black finish per Mil-Spec.
    • Length: 5.5″ long.
    • Weight: 1.2 oz.
    • Warranty: Lifetime.
    • Made In America By Men And Women Proud To Be Americans!

    • IMPORTANT NOTICE: THE NEW 870 SHOTGUNS PRODUCED BY REMARMS HAVE ONLY THREE THREADED HOLES AT THE TOP OF THE RECEIVER FOR THE MOUNTING OF A SCOPE, VERSUS FOUR.  THIS IS THE GG&G SCOPE MOUNT TO FIT THIS NEW CONFIGURATION.

    • WILL ONLY FIT REMARMS REMINGTON 870 SHOTGUNS WITH THREE 6-48 THREADED HOLES IN THE TOP OF THE RECEIVER

     

GG&G Remington 870 Red Dot Scope Mount

Remington 870 Red Dot Scope Mount- Per RMR Footprint spec

REMINGTON 870 RED DOT SCOPE MOUNT:

Many of our customers asked us to manufacture a Red Dot Scope Mount for the Remington 870 Shotgun. So we did. The GG&G Remington 870 Red Dot Scope Mount has the RMR fitment or attachment layout. However, the 870 Red Dot Scope Mount with that layoiout fits approximately 20 other red dot optics, but beware of screw lengths. The mounting hardware supplied in this package is only tested to fit the Trijicon RMR optic. Some optic mounting screws may be too long and contact the top of the Remington 870 receiver.

The Remington Red Dot Scope Mount is a rock solid low profile mount. It is CNC machined to precise tolerance and has a solid engagement with the top of the 870 receiver and the red dot optic.  The Red Dot Scope Mount for the Remington 870 coupled with the RMR Red Dot Scope, provides a rugged and accurate quick target acquisition package.

 

REMINGTON 870 RED DOT SCOPE MOUNT SPECIFICATIONS:

  • Does not require any modifications to your Remington 870 Shotgun
  • The Remington 870 Red Dot Mount easly installs on 3 and 4 hole tapped receivers.
  • Includes mounting hardware for the Remington 870 Mount and hardware specifically for mounting the Trijicon RMR to the scope mount.
  • Hex key wrenches are included.
  • The Remington 870 Red Dot Scope Base fits several other red dot optics but beware of screw lengths. The mounting hardware supplied in this package is only tested to fit the Trijicon RMR optic.
  • Red Dot Fitment List: Trijicon RMR / Trijicon SRO / Holosun 407C / Holosun 407C V2 / Holosun 407C X2 / Holosun 507C / Holosun 507C V2 / Holosun 507C X2 / Holosun 508T / Holosun 508T X2 /Riton X3 Tactix PRD/ NcStar VISM FlipDot Pro / ADE Advanced Optics RD3-020 Raptor / ADE Advanced Optics RD3-023 Valkyrie / Swampox Kingslayer 1×22 / Swampfox Liberty RMR 1×22 / Swampfox Justice RMR 1×27 / Vector Optics Frenzy 1x22x26.
  • All edges are deburred for the shooter’s safety.
  • Rounded edges provide a snag free operation.
  • Material: The Remington 870 Red Dot Scope Mount is manufactured from 6061-T6 aluminum.
  • Length: 1.800″
  • Width: 1.100″
  • Thickness: .230″
  • Body Finish: Matte black Type III hard coat anodized per Mil-Spec to protect it from the elements.
  • Weight: 0.5 oz.
  • Warranty: Lifetime.
  • Made in America By Men And Women Proud To Be Americans!

  • IMPORTANT NOTICE! Although we include mounting screws for the Trijicon RMR, there are approximately 20 other Micro Red Dot Optics that fit the GG&G Remington Red Dot Scope Mount. A fitment list is provided in the Specification section below.

    Please be advised that the screws that are included with the GG&G Red Dot Mount are specific to mounting the RMR and may be too long for mounting other red dot optics. For example three Holosun Mini Red Dot Scopes, models 407, 507 and 508 have the same attachment screw layout as the Trijicon RMR. However, BE ADVISED: The screws that come with the GG&G Remington 870 RMR Mount ARE TOO LONG TO MOUNT THE HOLOSUN OPTICS! If you attempt to mount these Holosuns or any of the other optics listed below, you may dimple the top of the receiver!

    Ensure you have the proper length screws prior to installing any other optic than the Trijicon RMR!  PROCEED WITH CAUTION! DAMAGE TO YOUR RECEIVER COULD OCCUR.

GG&G Remington 870 Red Dot Scope Mount Burris Fastfire 3 and 4 Footprint

Remington 870 Red Dot Scope Mount- Burris Fastfire 3 and 4 Footprint

REMINGTON 870 SHOTGUN RED DOT SCOPE MOUNT-BURRIS FASTFIRE FOOTPRINT

Mini Red Dot Optics like the Burris FastFire 3 and FastFire 4 are super popular as a red hot tactical setup for shotguns. This GG&G Remington 870 Red Dot Optic Mount has the fitment or attachment layout of the Burris FastFire 3 and FastFire 4 Optic. Please keep in mind that many red dot manufacturers use the same footprint layout. That’s why the GG&G 870 Low Profile Red Dot Scope Base fits approximately five other red dot optics but please beware of screw lengths. The mounting hardware supplied in this package is only tested to fit the FastFire 3 and 4 optics.

The Remington 870 Shotgun Red Dot Mount is low profile and a solid mount for the 870 . CNC machined to precise tolerance, insures a rock solid engagement with the top of the Remington receiver and the red dot scope. The 870 Red Dot Scope Mount coupled with either the Burris FastFire 3 or FastFire 4 Red Dot Scope or any of the red dots having the same footprint, provide a rugged and accurate quick target acquisition package.
 

REMINGTON 870 SHOTGUN RED DOT SCOPE MOUNT WITH BURRIS FASTFIRE FOOTPRINT SPECIFICATIONS:

  • Does not require any permanent modifications to your Remington 870 except removal of the standard dovetail scope mount.
  • The Remington 870 Red Dot Scope Mount For FastFire’s is easy to install using factory drilled and tapped mounting holes.
  • Includes mounting hardware for mounting the FastFire 3 and 4 Scope Mount to the Remington 870 receiver and hardware specifically for mounting the Burris FastFire 3 and 4 to the scope mount.
  • Hex key wrenches are included.
  • The Remington 870 Shotgun Red Dot Scope FastFire base fits several other red dot optics but beware of screw lengths. The mounting hardware supplied in this package is only tested to fit the Burris FastFire 3 and 4 optics.
  • Red Dot Fitment List: Primary Arms SLX RS-10, SightMark Mini Shot M-Spec and Mini Shot Pro Spec, Vortex Venom, Vortex Viper.
  • All edges are deburred for the shooter’s safety.
  • Rounded edges provide a snag free operation.
  • Material: 6061-T6 aluminum.
  • Length: 1.965″.
  • Width:  1″.
  • Thickness: .250″.
  • Body Finish: Matte black Type III hard coat anodized per Mil-Spec to protect it from the elements.
  • Weight: 0.5 oz.
  • Warranty: Lifetime.
  • Made in America By Men And Women Proud To Be Americans!

  • IMPORTANT NOTICE! Although we include mounting screws for the Burris FastFire 3 and FastFire 4 red dot optics, there are approximately 5 other Micro Red Dot Optics that fit this GG&G Remington 870 Red Dot Scope Mount. A fitment list is provided in the Specification section below.

    Please be advised that the screws that are included with this GG&G Red Dot Mount are specific to mounting the FastFire 3 and 4 and may be too long for mounting other red dot optics. If you attempt to mount any of the optics listed below or others not specifically listed without verifying screw lengths, you may dimple the top of the receiver!

    Ensure you have the proper length screws prior to installing any other optic than the Burris FastFire 3 and FastFire4!  PROCEED WITH CAUTION! DAMAGE TO YOUR RECEIVER COULD OCCUR.

GG&G Remington Tac 14 Side Saddle Shell Holder

Remington Tac 14 Side Saddle Shell Holder

REMINGTON TAC-14 FIVE SHOT SIDE SADDLE SHELL HOLDER

The GG&G Remington TAC-14 Side Saddle Shell Holder (Five Shot) provides fast access to your rounds at an angle that matches your hand. The GG&G Remington TAC-14 Side Saddle facilitates loading the mag tube and the chamber. Additionally, you have the option of purchasing your TAC-14 Side Saddle with the TAC-14 QD Sling Attachment.

Important Consideration: Unlike other shotgun side saddle shell holders, the GG&G TAC-14 Side Saddle utilizes a solid rubber tube shell retainer versus a rubber tube shell retainer with side walls. The Reason? The rubber tube type shell retained easily distorts from heat and continuous pressure of the shotgun shell. Over time the shell becomes loose in the shell holder. The GG&G solid shell retainer with a speced durometer reading, retains its form resulting in a tight fit that you can count on for years of use.

REMINGTON TAC-14 FIVE SHOT SIDE SADDLE SHELL HOLDER SPECIFICATIONS:

  • Manufactured specifically for the 12ga Remington TAC-14.  Will not fit the 20ga TAC-14.
  • As easy to install as changing a car tire.
  • No modifications are required to the weapon for installation.
  • The TAC-14 Side Saddle mounts solidly to receiver using provided steel trigger pin replacement bolts.
  • Non-marring backing plate will not damage the receiver’s finish. The backing plate is cut out to view weapon’s serial number. The Remingto Side Saddle holds 12 ga ammunition at a unique angle of 15 degrees to facilitate the speed of bottom loading the magazine tube or top loading of the chamber.
  • With the Remington Side Saddle Shell Holder, shotshells can be retained in base up or base down position depending on shooter’s style of reloading.
  • The TAC-14 Side Saddle features a durable, oil resistant, replaceable shotshell retention system.
  • Manufactured from 6061 T-6 aluminum.
  • Type III hard anodized black per mil-spec.
  • Ergonomic design including lightning cuts for weight reduction.
  • Weight: 5.5 oz
  • Overall Length: 6.5″
  • All edges have been rounded for the shooter’s safety.
  • Warranty: Lifetime.
  • Made In America By Men And Women Proud To Be Americans!
  •